MB SLOT parts 27/04/2008
| Cod Art | Products |
| 07001 | Hard steel axle 3/32" 54 mm for sidewinder |
| 07002 | Anglewinder Crown 32T |
| 07003 | Sidewinder Crown 34T 19 mm |
| 07006 | Sidewinder Crown 36T 19 mm |
| 07007 | Springs for pick-up |
| 07008 | Magnet for suspension |
| 07009 | Song NA Motor 21.000 Rpm 12 volt "HIGH MAGNETIC POWER" |
| 07010 | Hard steel axle 3/32" 49 mm x 3/32" |
| 07011 | Short suspension kit without springs |
| 07012 | Hard steel axle 3/32" 49 mm with flat sections |
| 07013 | Special eyelets for Pick-Up/Motor cable connection |
| 07015 | Segger |
| 07020 | Unflanged low Balls Bearing, hole 3/32" for Art. 17020 |
| 07021 | Resistor for MB SLOT Hand Control 14.00 Ohm |
| 07022 | Resistor for MB SLOT Hand Control 16.80 Ohm |
| 07023 | Resistor for MB SLOT Hand Control 21.00 Ohm |
| 07024 | Resistor for MB SLOT Hand Control 25.20 Ohm |
| 07025 | Resistor for MB SLOT Hand Control 30,80 Ohm |
| 07026 | Resistor for MB SLOT Hand Control 37.80 Ohm |
| 07027 | Resistor for MB SLOT Hand Control 44.80 Ohm |
| 08001 | Motor power test kit with balance, without battery |
| 08002 | MOTOR POWER TEST KIT without balance |
| 08003 | DODO Motor 23000 rpm 12V "High Magnetic Power" (short case double axle) |
| 08004 | Pivots for magnetic suspensions |
| 08005 | Suspension heads Art. 19111 |
| 08006 | 4 x Suspension pivot Art. 190111 |
| 08007 | Hollow Hard Steel axle 3/32" 54 mm |
| 08009 | Nylon screws M2 x 12 |
| 08010 | Nylon M2 |
| 08011 | Eccentring Bearing For Axle 3/32" |
| 08020 | Magnesium wheel 15.80 x 10.00 mm for axle 3/32" - 0,7 gr |
| 08021 | Magnesium wheel 15.80 x 8.00 mm for axle 3/32" - 0,6 gr |
| 08022 | Magnesium wheel 15.80 x 10.00 mm concave for axle 3/32" - 0,7 gr |
| 08027 | 27T Anglewinder Crown |
| 08028 | 28T Anglewinder Crown |
| 08029 | 29T Anglewinder Crown |
| 08030 | 30T Anglewinder Crown |
| 17001 | GNIK 021 Motor 21.000 rpm 12 volt (long case) |
| 17002 | GNIK 023 Motor 23.000 rpm 12 volt (long case) |
| 17003 | KRAHS 023 Motor 23.000 rpm 12 volt, (short case, double axle) |
| 17020 | MB SLOT stopper with ball bearings for inline crown |
| 17024 | Crown, inline 24T |
| 17025 | Crown, inline 25T |
| 17026 | Crown, inline 26T |
| 17027 | Crown, inline 27T |
| 17030 | Pick up with screw (2 pcs) |
| 17031 | Pick up standard (2 pcs) |
| 17032 | Pick up with spring and screw (2 pcs) |
| 17033 | Pick up for metal chassis (Plafit) for NINCO track (2 pcs) |
| 18000 | Box for small parts |
| 18001 | Box for tools, 18 comparments |
| 18002 | Box for tools, composable comparments |
| 18005 | Box for single axles 3/32" 54 (pack of 5 pieces) |
| 18006 | Box for motors (pack of 5 pcs) |
| 18007 | Mini Bag |
| 18010 | Precision cross-head screwdeiver 00 |
| 18099 | Lock nut M2 (pack of 10 pcs) |
| 19005 | F1 rear wheels for axle 3/32" |
| 19006 | Wheels ergal 16.80 x 8.00 mm for independent axle Art. 19092 |
| 19007 | Wheels ergal 17.20 x 8.00 mm for axle 3/32" |
| 19008 | Wheels ergal, 15,80 x 8.00 mm. hollow, for tyres Art. 30013 |
| 19009 | Wheels ergal 18,10 x 10.00 mm for axle 3/32" |
| 19010 | Wheels, front, ergal 18.60 x 8.00 mm for Fly Truck (and Raid car) for axle 3/32" |
| 19011 | Wheels, rear, double ergal, for Fly Truck for axle 3/32" |
| 19012 | Wheels, ergal, 16,80 x 10.00 mm for axle 3/32" |
| 19013 | Wheels, ergal. 15,80 x 8.00 mm for axle 3/32" |
| 19014 | Wheels, ergal, MG Vanquish 15,80 x 12.00 mm for axle 3/32" |
| 19015 | Wheels, DELRIN, 15.80 x 8.00 mm for independent axle Art. 19092 |
| 19016 | Wheels, ergal, 17.20 x 10.00 mm for axle 3/32" |
| 19017 | Wheels, ergal 15.80 x 10.00 mm for axle 3/32" |
| 19018 | Wheels, ergal 16.80 x 8.00 mm for axle 3/32" |
| 19019/A | Wheels, lightweight, ergal, 17.20 x 8.00 mm. 0.75 gr for axle 3/32" |
| 19019/B | Wheels, lightweight ergal 17,20 x 10.00 mm 0.82 gr for axle 3/32" |
| 19020 | Bushing in bronze for MG Vanquish axle 3/32" |
| 19021 | Bushing in bronze for ProSlot axle 3/32" |
| 19022/B | Bushing in bronze for axle 3/32" type NINCO |
| 19023 | Bushing in bronze 2,50 mm type NINCO |
| 19024 | Bushing in bronze for AVANT transmission shaft |
| 19025 | Bushing in Derlin for axle 3/32" |
| 19026 | Bushing double, in Derlin for axle3/32" |
| 19027 | Bushing in Derlin for axle 2.50 mm type NINCO |
| 19029 | Exagonal grub screws M2,5 X 2,50 mm |
| 19030 | Exagonal grub screws M2 X 2.00 mm |
| 19031 | Exagonal grub screws M2 X 2,50 mm |
| 19032 | Exagonal grub screws M2 X 3.00 mm |
| 19033 | L Key for exagonal grub screws M2 |
| 19035 | Magnetizer and Demagnetizer for screwdrivers |
| 19036 | Pinion puller |
| 19037 | Pinion press |
| 19039 | Pivot for pinion puller |
| 19040 | Spacers 0.70 mm |
| 19041 | Spacers 0.50 mm |
| 19042 | Spacers 0.25 mm |
| 19043 | Spacers 3 mm |
| 19044 | Spacers 2 mm |
| 19045 | Spacers 1 mm |
| 19046 | Spacers 3 mm whit Exagonal grub screws axle 3/32" |
| 19047 | Pulley for 3/32" axle, for 4x4 cars |
| 19050 | Ball bearings, double-flange |
| 19060 | Liquid for cleaner motors |
| 19061 | Oil for bushing and axles |
| 19062 | "Magic Tyres" liquid tyre softener |
| 19063 | "Grip" liquid for tyres, 50 ml |
| 19064 | Cleaner for contacts 50 ml |
| 19065 | Bottle for liquids, capacity 50 ml with dropper and stopper |
| 19066 | Bottle OIL with empty needle |
| 19079 | Tinned contact braids |
| 19080 | Contact braids 1 m |
| 19081 | Motor cable brass eyelets 10x |
| 19082 | Motor cable brass eyelets 10x |
| 19090 | Hardened steel 54 mm 3/32” axle |
| 19091 | Three standard axles |
| 19092 | Kit indipendent front axles |
| 19093 | Transmission axles “Avant” |
| 19094 | Titanium axle 3/32" |
| 19101 | Springs kit for controllers HARD 24 |
| 19102 | Springs kit for controllers MEDIUM 27 |
| 19103 | Springs kit for controllers SOFT 30 |
| 19110 | Springs for “Avant” cars |
| 19111 | Kit sospension complete |
| 19112 | Set spring for Art. 19111 |
| 19113 | Kit 1 sospension without spring |
| 19150 | Driver/Cockpit inlet in Lexan Toyota supra Ninco |
| 19151 | Driver/Cockpit inlet in Lexan Honda NSX Ninco |
| 19152 | Driver/Cockpit inlet in Lexan Megane NINCO |
| 19153 | Driver/Cockpit inlet in Lexan Sauber Slot.it |
| 19154 | Driver/Cockpit inlet in Lexan TOYOTA GT1 |
| 19201 | Photoetched inserts for 5 spokes type hub 16,80 mm |
| 19201 | Photoetched inserts for 5 spokes type hub 15,80 mm |
| 19202 | Photoetched inserts for BBS type hub 16,80 mm |
| 19202 | Photoetched inserts for BBS type hub 15,80 mm |
| 19203 | Photoetched inserts for 18 spokes type hub 16,80 mm |
| 19203 | Photoetched inserts for 18 spokes type hub 15,80 mm |
| 19205 | Photoetched inserts for Fly Ferrari Classic type hub 15,80 mm |
| 19205 | Photoetched inserts for Fly Ferrari Classic type hub 16,80 mm |
| 19206 | Photoetched inserts for Fly Porsche Classic type hub 16,80 mm |
| 19206 | Photoetched inserts for Fly Porsche Classic type hub 15,80 mm |
| 19225 | Set pinion 8T 9T 10T 11T for crown in line MB SLOT |
| 19249 | 8 tooth pinion inline in steel |
| 19250 | 9 tooth pinion inline in steel |
| 19251 | 10 tooth pinion inline in steel |
| 19260 | 11 tooth pinion denti side/anglewinder in steel |